Xbox HDMI Port Repair in Manor, TX
TV says “No Signal”? Picture flickering or gone completely? A damaged HDMI port is one of the most common Xbox failures — and one of our specialties. We micro-solder a brand-new port onto the board right here in Manor, TX, usually in 1–3 hours, for gamers all over East Austin, Pflugerville, Round Rock, Elgin and beyond.
Signs your HDMI port is the problem
| ❌ “No Signal” on the TV even though the console powers on |
| ❌ Picture only shows when the cable is held at an angle |
| ❌ Bent, pushed-in, or visibly damaged pins inside the port |
| ❌ Intermittent flickering or signal dropouts mid-game |
Sometimes it isn’t the port at all — on some Xbox consoles the HDMI retimer chip fails instead. We diagnose at board level and tell you exactly which repair you need before any work starts.
Is it really the HDMI port? Check this before you drive over
A dead picture does not always mean a dead port, and we would rather you find that out at home than after a trip to Manor. Work through these in order — if the picture comes back at any point, you have saved yourself a repair.
| 1. Swap the HDMI cable. Use one you know works from another device. Cheap cables fail far more often than ports do. |
| 2. Try a different input, then a different TV. A blown HDMI input on the TV looks exactly like a blown port on the console. |
| 3. Confirm the console is actually running. Power light on, fan audible, controller connecting? Then the Xbox itself is alive and the fault sits somewhere in the video path. |
| 4. Boot in low-resolution mode. Hold the power button 10–15 seconds to shut down fully, then hold the power button together with the eject button — or the pair button on the diskless Series S — until you hear two tones. That forces 640×480, which sometimes gets a picture back when a handshake is failing. |
| 5. Look inside the port with a flashlight. Bent, flattened or missing pins, or a port that wiggles when you touch it, means hardware. |
If you only get a picture while holding the cable at a certain angle, stop testing and unplug it. That is a cracked solder joint, and every extra wiggle risks tearing a pad off the board and turning a straightforward repair into a much harder one.
What actually breaks an Xbox HDMI port
The HDMI port on every modern Xbox is soldered straight to the mainboard. There is no plug-in module to swap out, which is why a big-box store will tell you the console is a write-off, and why this is board-level micro-soldering rather than a parts change.
Nearly every failure we see is mechanical. Someone trips over the cable. The console gets knocked off a shelf while it is still plugged in. It gets carried to a friend’s house with the cable dangling. A younger sibling pulls it out sideways. All of that puts leverage on a connector that was never designed to take it, and the tiny solder joints underneath crack, or the pins bend far enough to short against each other.
Because the retimer can fail on its own, guessing is expensive. Fitting a new port to a console whose retimer is the real problem fixes nothing. That is why the diagnostic comes first and costs you nothing: we confirm which of the two failed before anyone commits to a repair, and if it turns out to be neither, you still owe us nothing.
HDMI port repair pricing — parts & labor included
| Xbox Series X — HDMI port replacement | $159.99 |
| Xbox Series S — HDMI port | $129.00 |
| Xbox One S — HDMI port | $109.99 |
| PlayStation 5 — HDMI port | $159.99 |
| PlayStation 4 — HDMI port | $99.00 |
🔧 Fixing two things at once? The second repair on the same console is $50 to 50% off — a deep clean alongside your HDMI repair is the most popular combo.
Every Xbox HDMI repair includes
- Free diagnostic. We open it up and tell you whether it’s the port or the retimer chip before you commit to anything. $0, always.
- No fix, no fee. If we can’t bring it back, you don’t pay for the attempt.
- 60-day warranty. Every repair we do is covered for 60 days. If the port fails again in that window, bring it back and we’ll sort it.
Rated 4.8★ by 95+ Google reviewers · Walk-ins welcome Mon–Fri 10am–7pm, Sat 10am–5pm.
Every repair is done in-house by our board-level micro-soldering techs — we never mail your console to a third party. Bring just the console (no cables or controllers needed), grab a coffee in Manor, and pick it up the same visit in most cases. We also accept mail-in console repairs from anywhere in Texas.
How we replace an Xbox HDMI port, step by step
All of it happens at the bench here in Manor. Your console never gets boxed up and sent to a third party, and it never leaves the shop.
| Diagnose. We test the console on our own display and cables, inspect the port under a microscope and confirm whether it is the port or the retimer before quoting anything. Free, every time. |
| Strip it down. Covers, fan, heatsink and shielding come off, and the mainboard comes out of the chassis. |
| Remove the old port. Controlled hot air lifts the damaged connector without cooking the components sitting beside it, then the pads are cleaned back to bare copper. |
| Fit the new port. A fresh connector goes on under the microscope, and every joint is inspected before power touches the board again. |
| Rebuild and retest. Fresh thermal compound, everything back together, then a real test on a 4K panel — picture, HDR and audio — with the console under load before we hand it back. |
Is it worth repairing, or should I just buy a new one?
A port replacement runs $159.99 on a Series X, $129.00 on a Series S and $109.99 on an Xbox One S — a fraction of what a new console costs. The money is only half of it, though. Everything on the console stays exactly where it is: your installed library, your saves, your achievements, your logins. No re-downloading several hundred gigabytes over a home connection, no migrating anything, no setting a new console up from scratch. And a console that gets fixed is a console that is not in a landfill.
The one case where we will tell you not to bother is when the damage runs past the port and into the board itself. It happens. We will show you what we are looking at, and you will not be charged for finding out.
Where we are, and who we fix consoles for
We are at 209 Lexington St, Manor, TX 78653, open Monday to Friday 10am–7pm and Saturday 10am–5pm, closed Sunday. Walk in with the console under your arm — no cables, no controllers, no appointment needed. Most HDMI repairs are finished while you wait, usually inside 1–3 hours.
Gamers drive to us from Manor, East Austin, Pflugerville, Round Rock, Elgin and across the wider Austin metro, and we take mail-in consoles from anywhere in Texas. If you are not sure whether it is worth the trip, call or text 512-774-4376 or 512-996-7134 and describe what the TV is doing — we can usually tell you over the phone.
Device Hero is an independent repair shop. We are not affiliated with, authorized by, or endorsed by Microsoft. Xbox, Xbox Series X, Xbox Series S and Xbox One are trademarks of Microsoft Corporation.
“Took my Series X here after some HDMI issues that ended up being the retainer chip. They were super communicable with updates on my console. Pricing was straightforward with no hidden fees.”
— Luiz H. · ★★★★★ Google review
📞 Call or Text 512-774-4376 or 512-996-7134 · See All Repair Prices →
Xbox HDMI repair FAQ
How much does it cost?
$159.99 for a Series X HDMI port replacement, $129.00 for a Series S, and $109.99 for an Xbox One S — parts and labor included. 8.25% TX sales tax is added at checkout.
How long does it take?
Usually 1–3 hours depending on workload. Call or text ahead and we’ll confirm your window before you drive over.
Do I need to bring anything besides the console?
Nope — just the console. Leave the cables and controllers at home.
Is it worth repairing?
Almost always — it’s a fraction of the price of a new console and your data never leaves the machine.
Also see: all game console repairs · full price list · PS5 HDMI port repair